The 228/232 camshafts use lobes that are designed to be both beehive & double valve spring friendly.
The 228/232 camshaft is available in a wide variety of lobe separations. The most popular options customers select is either the 112 LSA or the wider 114 LSA. The 112 LSA helps to bring the camshafts powerband lower in the rpm band. The lower LSA also creates a slightly rougher idle.
The 228/232 camshaft is a very popular camshaft for customers wanting a very streetable camshaft that makes approximately 5-7 more horsepower than the 228R camshaft. Dyno testing has shown the 228/232 camshaft to make a solid 50-55 RWHP gains with all other supporting bolt-on modifications in place. The 228/232 camshaft is large enough that we recommend a minimum 2,800 RPM stall converter in automatic cars. Tuning will also be required in both automatic & manual applications.
Purchase the naturally aspirated verison of the camshaft that Cleetus McFarland is running in "Leroy", his savage C5 Corvette! The naturally aspirated version of the Bald Eagle camshaft is a great choice for engines running cathedral-port cylinder heads and not running a supercharger. It will have a little bit more chop at idle vs. the boosted version of the Bald Eagle cam. It comes with a large dose of 'murica and full of bald eagles! While we will not release the complete specs of the camshaft, we can tell you that the duration @ .050" is 227/234 for the intake and exhaust, respectively. It is an easy camshaft to tune and has a nice lope at idle. Automatic-equipped vehicles will require a minimum of a 2,800 RPM stall speed torque converter. This cam can easily be daily driven with zero issues once tuned properly. The Bald Eagle cam can be run with either the PAC Racing 1219 single beehive valve springs or our TSP dual spring kit that includes PAC Racing polished dual valve springs, titanium retainers, spring seats, and valve seals.
Purchase the same camshaft that Cleetus McFarland is running in "Leroy", his savage 427 CID C5 Corvette! The Bald Eagle camshaft was custom-ground for Leroy and is a great choice for twin turbocharged applications with 400+ cubic inches. This cam comes with a large dose of 'murica and full of bald eagles! Do it for Dale! You can see the initial start-up video of Leroy with his 427 CID and hear this camshaft idle in the link below:
This camshaft has a nice lope at idle, and automatic-equipped vehicles will require a minimum of a 3200 RPM stall speed torque converter. This cam can easily be daily driven with zero issues once tuned properly. The twin turbo stroker Bald Eagle cam will require our TSP dual spring kit that includes PAC Racing polished dual valve springs, titanium retainers, spring seats, and valve seals.
The TSP Stage 3 Turbo Cam is intended for 4,8, 5.3, 5.7, and 6.0 using single or twin-turbos. This camshaft will work in stock turbo’d applications or a wild built forged motor! Our Stage 3 Turbo cam will be sure to get every ounce of power possible out of your boosted setup. Our TSP double valve springs are recommended for this cam and turbo applications for extra reliability and safety, as well as our chromoly hardened pushrods.
Engines best suited for: 4.8, 5.3, 5.7, 6.0'
Desired Compression ratio for cam: 9.5:1 – 10:.5:1
Recommended Springs Required: Pac 1219 or TSP .660 Double Valve Spring
Aftermarket Stall Converter Required: Yes, 2800+
Upgraded Rear Gear Required: No, but Automatics should be at least a 3.23
Operating RPM Range: 2000-6600
Estimated Power Increase: 50+
Drivability: Will drive like stock but with some decent lope at idle.
For more information and help regarding camshaft selection, give us a call at 512-863-0900 and speak with one of our knowledgeable sales reps to discuss your camshaft needs!
TSP 224/228 .600"/.600" Camshaft
Regular price
$389.99
Save $-389.99
The 224/228 camshafts use lobes that are designed to be both beehive & double valve spring friendly.
The 224/228 camshaft is available in a wide variety of lobe separations. The most popular options customers select is either the 112LSA or the wider 114LSA. The 112LSA helps to bring the camshafts powerband lower in the rpm band. The lower LSA also creates a slightly rougher idle. Boost applications typically stay at 114LSA or wider with this camshaft.
The 224/228 camshaft is a popular option for guys wanting more exhaust duration in combination with the 224 intake lobe. This camshaft is very popular for guys running very streetable boost engines. It has awesome drivability while making a solid 40+ rear wheel horsepower gains in N/A applications & even more in boost applications!
Texas Speed 228R Camshaft
Regular price
$389.99
Save $-389.99
The 228R camshafts use lobes that are designed to be both beehive & double valve spring friendly.
The 228R camshaft is available in a wide variety of lobe separations. The most popular options customers select is either the 112LSA or the wider 114LSA. The 112LSA helps to bring the camshafts powerband lower in the rpm band. The lower LSA also creates a slightly rougher idle.
The 228R camshaft is a very popular camshaft for customers wanting a very streetable camshaft that makes approximately 5-7 more horsepower than the 224R camshaft. Dyno testing has shown the 228R camshaft to make a solid 45-50rwhp gains. The 228R camshaft is large enough that we recommend a larger than stock stall converter in automatic cars. Tuning will also be required in both automatic & manual applications.
